From RegConfig in Connect mode via cable or Web Connection mode it is possible to see all the available alarms by entering the Alarms page:
...
Once the alarm has been resolved, the red light turns off without any further operations.
Attention
Errors from 16 to 23 (Circuit limit temperature) must be reset by switching the heat/cold enable off and on again or by switching off and on the power supply to the REG.
ALARM LIST | |||
Code | Description | Code | Description |
1 | Outdoor Air Probe Error | 57 | Pompa C1 Water Pump B collettore 1 |
2 | DHW Probe Error | 58 | Pompa C2 Water Pump A collettore 2 |
3 | Buffer Tank Probe Error | 59 | Pompa C2 Water Pump B collettore 2 |
4 |
| 60 | Pompa C3 Water Pump A collettore 3 |
5 |
| 61 | Pompa C3 Water Pump B collettore 3 |
6 | TSP out of range | 62 | Pompa C4 Water Pump A collettore 4 |
7 | Comunicazione OT Caldaia KO | 63 | Pompa C4 Water Pump B collettore 4 |
8 | Circ. 1 Sensor | 64 | Pompa C5 Water Pump A collettore 5 |
9 | Circ. 2 Sensor | 65 | Pompa C5 Water Pump B collettore 5 |
10 | Circ. 3 Sensor | 66 | Pompa C6 Water Pump A collettore 6 |
11 | Circ. 4 Sensor | 67 | Pompa C6 Water Pump B collettore 6 |
12 | Circ. 5 Sensor | 68 | Pompa C7 Water Pump A collettore 7 |
13 | Circ. 6 Sensor | 69 | Pompa C7 Water Pump B collettore 7 |
14 | Circ. 7 Sensor | 70 | Pompa C8 Water Pump A collettore 8 |
15 | Circ. 8 Sensor | 71 | Pompa C8 Water Pump B collettore 8 |
16 Temperatura limite collettore 1 | C1 Limit. Temp. | 72 | Sorgente Source 1 |
17 Temperatura limite collettore 2 | C2 Limit. Temp. | 73 | Sorgente Source 2 |
18 Temperatura limite collettore 3 | C3 Limit. Temp. | 74 | Sorgente Source 3 |
19 Temperatura limite collettore 4 | C4 Limit. Temp. | 75 | UGW 8 |
20 Temperatura limite collettore 5 | C5 Limit. Temp. | 76 | UGW 9 |
21 Temperatura limite collettore 6 | C6 Limit. Temp. | 77 | UGW 10 |
22 Temperatura limite collettore 7 | C7 Limit. Temp. | 78 | Allarme OT Gen . OTAlarm |
23 Temperatura limite collettore 8 | C8 Limit. Temp. | 79 | Allarme Tutti Gen. OTAll OT Gen Alarm |
24 | Sonda zona Zone 1 Sensor | 80 | Sonda Sorgente Source 1 Probe |
25 | Sonda zona Zone 2 Sensor | 81 | Sonda Sorgente Source 2 Probe |
26 | Sonda zona Zone 3 Sensor | 82 | Sonda Sorgente Source 3 Probe |
27 | Sonda zona Zone 4 Sensor | 83 |
|
28 | Sonda zona Zone 5 Sensor | 84 |
|
29 | Sonda zona Zone 6 Sensor | 85 |
|
30 | Sonda zona Zone 7 Sensor | 86 |
|
31 | Sonda zona Zone 8 Sensor | 87 |
|
32 | Sonda zona Zone 9 Sensor | 88 | Ingresso allarme Free Alarm 1 |
33 | Sonda zona Zone 10 Sensor | 89 | Ingresso allarme Free Alarm 2 |
34 | Sonda zona Zone 11 Sensor | 90 | Ingresso allarme Free Alarm 3 |
35 | Sonda zona Zone 12 Sensor | 91 | Ingresso allarme Free Alarm 4 |
36 | Sonda zona Zone 13 Sensor | 92 | Ingresso allarme Free Alarm 5 |
37 | Sonda zona Zone 14 Sensor | 93 | Ingresso allarme Free Alarm 6 |
38 | Sonda zona Zone 15 Sensor | 94 | Ingresso allarme Free Alarm 7 |
39 | Sonda zona Zone 16 Sensor | 95 | Ingresso allarme Free Alarm 8 |
40 | Sonda zona Zone 17 Sensor | 96 |
|
41 | Sonda zona Zone 18 Sensor | 97 |
|
42 | Sonda zona Zone 19 Sensor | 98 |
|
43 | Sonda zona Zone 20 Sensor | 99 |
|
44 | Sonda zona Zone 21 Sensor | 100 |
|
45 | Sonda zona Zone 22 Sensor | 101 |
|
46 | Sonda zona Zone 23 Sensor | 102 |
|
47 | Sonda zona Zone 24 Sensor | 103 |
|
48 | Sonda zona Zone 25 Sensor | 104Sonda solare 1 | S1 Solar Probe |
49 | Sonda zona Zone 26 Sensor | 105Sonda solare 2 | S2 Solar Probe |
50 | Sonda zona Zone 27 Sensor | 106Sonda solare 3 | S3 Solar Probe |
51 | Sonda zona Zone 28 Sensor | 107Sonda solare 4 | S4 Solar Probe |
52 | Sonda zona Zone 29 Sensor | 108Sonda solare 5 | S5 Solar Probe |
53 | Sonda zona Zone 30 Sensor | 109Sonda solare 6 | S6 Solar Probe |
54 | Sonda zona Zone 31 Sensor | 110 |
|
55 | Sonda zona Zone 32 Sensor | 111 |
|
56 | Pompa C1 Water Pump A collettore 1 |
|
|
BUS ERRRORS
The System provides a bus error signal by turning ON the yellow led on the REG-DIN-8.
If both alarms (red light on) and bus errors (yellow light on) are present on the REG-DIN-8, it is necessary to solve the bus error first as it could be the cause of the alarm. For example, if there were a communication problem with the REG-IOA expansion module to which the TP probe of zone 1 is connected there would be both a bus error (because the REG-DIN-8 and the REG-IOA do not communicate ), but also alarm 24 relating to the failure to read the temperature of zone 1. Once the bus error is resolved, the alarm is also resolved.
For more info about bus error trouble shooting see BUS REG WIRING BEST PRACTICE.