Associated Sensor
Normally a temperature (or temperature and humidity) sensor is associated to a zone via the Sensor parameter on the Configuration Zone/1 sub page:
PHOTO TBD
For more information on how to select sensors, see ANALOG AND DIGITAL INPUT MULTIPLEXER.
The Temperature and Humidity value of the selected sensor can be visualized on the left of the Zone page.
Note
Remember that a zone can also operate without associated sensor; in this case, when the zone is active (in Comfort, Economy, or Antifreeze Active mode), the corresponding output will be always active. Some possible uses of this configuration are:
...
Each individual zone can be associated with a temperature value correction, that is an Offset value that will be added (or subtracted, if negative) to the value detected by the temperature probe. This value is set in the Configuration Zone/2:
PHOTO TBD
Temperature and Room Humidity Set Point
...
Summer Comfort Set: used if the set season is Summer and the working mode is Comfort.
Summer Economy Set: used if the set season is Summer and the working mode is Economy.
Winter Comfort Set: used if the set season is Winter and the working mode is Comfort.
Winter Economy Set: used if the set season is Winter and the working mode is Economy.
Humidity Set: used in both seasons, either in Economy or Comfort
PHOTO TBD
The current set temperature is on the left side of the Zone Page.
Note
From version 4.30 of the REG Firmware, a new Function is available, which also allows you to manage a humidity economy set point (see ECONOMY FUNCTION FOR THE DEHUMIDIFIERS).
...
Temperature and Humidity Set Point
...
I limiti si impostano nella pagina Configurazione 1:
...
Attenzione
...
Limits
Limits are set on Configuration 1 page:
PHOTO TBD
Warning
If RegConfig is used, these limits are bypassed, while they can’t be bypassed by REG-TFT and REG-DOT-B e dai sensori display and by REG-THL-SXX .
Isteresi di Temperatura e Umidità
Al fine di evitare attivazioni/disattivazioni repentine della zona per valori di tempertatura in prossimità del set impostato viene utilizzata una isteresi (solitamente nell'ordine di sensors
Temperature and Humidity Hysteresis
In order to avoid sudden activation/deactivation of the zone for temperature values close to the set point, a hysteresis is visualized (usually in the range of 0,3-1,0 °C), la cui modalità di intervento varia sempre in funzione della stagione attuale:
Se il sistema è in Inverno la Zona si disattiverà al raggiungimento di un valore di temperatura pari a Set+Isteresi e si attiva se il sensore è < set point.
Se il sistema è in Estate la Zona si disattiverà al raggiungimento di un valore di temperatura pari a Set-Isteresi e si attiverà se il sensore è > set point.
Per l’umidità, invece, la richiesta si disattiva sempre al set point - isteresi (che di solito è impostata a 5%).
Anche le isteresi di Temperatura e Umidità vengono impostate uguali per tutte le zone in Configurazione 1:
...
Quindi se il set point di una zona è 21°C, la zona si attiverà sotto 21°C e si disattiverà sopra i 21,3°C in riscaldamento. Se il set point di umidità è 55%, la zona (se ha un sensore di umdità) attiva la richiesta di deumidificazione sopra il 55% e la interrompe sotto il 0° C), of course it works in different ways according to the current season:
If the system is in Winter, the Zone will deactivate when a temperature value equal to Set+Hysteresis is reached and will activate if the sensor is < set point
If the system is in Summer the Zone will deactivate when a temperature value equal to Set – Hysteresis is reached and will activate if the sensor is > set point.
On the other hand, for humidity the request will always deactivate at set point – hysteresis (that is usually set to 5%).
Temperature and Humidity hysteresis are also set equal for all the zones in Configuration 1:
PHOTO TBD
So, if the set point of a zone is 21°C, the zone will activate below 21°C and will deactivate above 21,3°C in heating. If the humidity set point is 55%, the zone (if it has a humidity sensor) will activate the dehumidification request above 55% and deactivate it below 50%.